Key Takeaways

  • The die line is the cut. Background art runs 0.125″ past it on all four sides, and nothing that matters sits within 1/16″ inside it.
  • Can label size is set by the die, not by the can’s volume. TLF Graphics publishes 17 craft beverage die line templates covering 12 oz, 12 oz sleek, 16 oz, crowler and keg collar formats.
  • Corner radius is part of the tool. The same 8″ x 3.5″ label exists with a 0.125″ radius and with a 0.0156″ radius, and they are not interchangeable.
  • Build in Adobe Illustrator, set the document to CMYK, keep images at 300 PPI, outline the fonts and call out Pantone colors by number. Word, PowerPoint and Publisher files are not print files.
  • Send an unwind position with the order. There are eight, and the applicator on the filling line takes one of them.

A can label job usually stops for one of three reasons. The artwork is the wrong size for the die. The file was built in software prepress cannot open cleanly. Or the roll arrives wound the wrong way for the applicator at the cannery.

All three are decided in the design file, weeks before anything prints. This is the specification sheet for getting them right: the die sizes TLF Graphics publishes for craft beverage work, what bleed and safe zone actually mean on a label, how to build a file that does not need rebuilding, what makes a barcode scan, and how to name an unwind position.

What a die line is, and what sits around it

Three terms do most of the work on a label layout, and TLF’s art resources page defines all three in its art department guidelines.

  • Die line. The actual cut of the final design. It is a tool on a press, not a rectangle in your file. If your artwork does not match a die the job can run on, something has to change, and it will not be the die.
  • Bleed. Extend the background of the artwork into the bleed area at least 1/8″, which is 0.125″, on all sides. Without it, the smallest movement in the web shows as a white sliver along one edge of the finished label.
  • Safe zone. Do not place important text or images within 1/16″ of the die line. That band is where cutting tolerance lives. Background runs past the die line; content stops short of it.

Said plainly: art goes past the cut, words stay away from it. Most of the revisions a prepress department sends back on a first-time label are one of those two rules.

The craft beverage die sizes TLF publishes

TLF Graphics puts its die line templates on the art resources page as downloadable PDFs, grouped by container. Each file states its own die size and corner radius. These are the current craft beverage templates.

Container Die size (w x h) Corner radius
12 oz can 7″ x 3.5″ 0.125″
12 oz can 8″ x 3.5″ 0.125″
12 oz can 8″ x 3.5″ 0.0156″
12 oz can 8.5″ x 3.5″ 0.125″
12 oz can 8″ x 3.25″ 0.125″
12 oz can 8″ x 3.625″ 0.125″
12 oz sleek can 6.875″ x 5.375″ 0.125″
12 oz sleek can 7″ x 5.4″ 0.0156″
12 oz sleek can 7.125″ x 5.375″ 0.125″
16 oz can 7.5″ x 5″ 0.125″
16 oz can 8″ x 5″ 0.125″
16 oz can 8.0625″ x 5″ 0.125″
16 oz can 8.0625″ x 5″ 0.015″
Crowler 10″ x 6″ 0.125″
Keg collar 6.75″ x 6.75″ not applicable
General 5″ x 3.5″ square corners
General 7.125″ x 3.625″ square corners

Two things are worth reading off that table before you start drawing.

A 12 oz can and a 12 oz sleek can are not the same label. They hold the same volume in a different shape, and the templates show it: the standard 12 oz dies are roughly 3.25″ to 3.625″ tall, the sleek dies are around 5.375″ tall and slightly narrower. A label built for one will not wrap the other.

The same nominal size can exist as two different dies. There is an 8″ x 3.5″ twelve-ounce die with a 0.125″ corner radius and another with a 0.0156″ radius, and a 16 oz 8.0625″ x 5″ in both 0.125″ and 0.015″. A corner radius is cut by the tool. Rounding the corners in your artwork instead of downloading the matching template does not change what the press does.

Download the template for the die your job will run on and build inside it. If you are not sure which one that is, say what the can is and who is filling it, and the answer comes back before any art is drawn.

Build a file that does not need rebuilding

The art department guidelines on the same page are short, and every line in them exists because a job was once delayed by its opposite.

  • Software. Adobe Illustrator is the industry standard for labels and packaging. Adobe PDF, Adobe InDesign and Adobe Photoshop files are also accepted. Files from Microsoft Publisher, PowerPoint or Word are generally not suitable for digital prepress.
  • Resolution. Placed images should be at least 300 PPI. Low-resolution files print blurry or blocky, and nothing in prepress can add detail that was never captured.
  • Linked images. Embed every linked file, or send the linked images with the document. A missing link is the most common reason a package arrives incomplete.
  • Type. Convert fonts to outline, or include a copy of the fonts with the file.
  • Color. Set the document color mode to CMYK, not RGB. Call out Pantone colors by number, or supply a physical color sample to match.
  • Packaging. Compress the job before sending it. A .zip speeds the transfer and protects the files from corruption in transit.

Color mode is the one that costs the most when it is missed. A design approved on a backlit screen in RGB will shift when it is separated for print, and the shift usually lands on the brand color somebody chose years ago. Naming the Pantone takes a sentence and settles it.

Artwork spec

The five numbers on a print-ready label file

Each one is a hard requirement, not a preference, and each is checked before the job is scheduled.

0.125″
bleed, all four sides
1/16″
safe zone inside the die line
300 PPI
minimum image resolution
1.175″
smallest barcode width that scans
8
unwind positions to choose from

Source: TLF Graphics art department guidelines and web direction / unwind chart, both on the art resources page.

Barcodes that actually scan

A barcode is the one element on a beverage label that either works or does not, and it is usually sized by eye. The guidelines give real numbers.

Overall barcode size Width Height
Minimum 1.175″ 0.816″
Normal 1.469″ 1.02″
Maximum 2.938″ 2.04″

Two rules sit alongside the size. The quiet zone, the empty space around the symbol that tells the scanner where the code begins and ends, should be at least 0.125″. And contrast has to be high: dark bars on a light background. Red bars and low-contrast combinations do not scan, however good they look in the layout.

Which symbology you need depends on what the code has to carry:

  • UPC-A identifies products in retail stores. If the can is going on a shelf, this is the one the buyer asks about.
  • Code 128 has no character limit, which suits shipping labels and any code that mixes data types.
  • GS1-128 encodes detailed product information such as batch or lot, serial number and expiration date.
  • Code 39, also written 3 of 9, turns up on name badges, inventory and industrial applications.
  • Data Matrix labels small electronic and industrial components where there is almost no room.
  • QR codes carry website links, contact information or payments, which on a beverage label usually means the brand story or a loyalty program.

Unwind direction, the spec nobody sends

Roll labels have an orientation on the roll, and the applicator at the cannery or co-packer accepts exactly one. TLF publishes a web direction and unwind chart with the eight standard positions, and it is worth looking at before the order goes in rather than after the pallet arrives.

The eight split into two groups of four:

  • Positions 1 to 4 are wound out. The labels sit on the outside of the roll.
  • Positions 5 to 8 are wound in. The labels sit on the inside of the roll.

Within each group, the number says which edge of the design comes off the roll first: top of the design first (1 and 5), bottom first (2 and 6), right-hand side first (3 and 7), left-hand side first (4 and 8).

Nobody has to memorize that. The practical step is to ask whoever runs the applicator which position their line takes, write the number on the purchase order, and keep it on file for reorders. A perfectly printed roll in the wrong unwind is a reprint, and it is a reprint that nobody catches until the line is already set up.

Keg collars and the logos you are allowed to print

Keg collars use their own die: 6.75″ square, with a center hole rather than a corner radius. The same bleed and safe zone rules apply, and the printable area is tighter than it looks because the collar has to clear the keg’s neck. Our guide to keg collars covers the ordering side of that format.

The art resources page also carries official logo files that craft beverage brands are routinely asked to place, in print-quality PDF: the Independent Craft Beer logo, the Think NY Drink NY mark, and the New York State Brewers Association logo in color and in black and white. Pulling one of those off a web page as a low-resolution PNG is the other way a can label fails its preflight. Download the vector file.

What to have ready when you order

Everything above collapses into a short list. A craft beverage label order moves straight to production when it arrives with:

  • The die line template the job runs on, named by size and corner radius.
  • Artwork bled 0.125″ on all four sides, with nothing important inside the 1/16″ safe zone.
  • A CMYK document, images at 300 PPI or better, fonts outlined or supplied, links embedded.
  • Pantone numbers for the brand colors, or a physical sample to match.
  • A barcode at or above the minimum size, with a 0.125″ quiet zone and dark bars on a light ground.
  • The unwind position the filling line takes.
  • Quantity, number of versions, and the finish or material you expect.

Labels in this category are printed on roll, and the press that suits a pilot batch is not the one that suits a year of a flagship SKU. Our overview of print technologies covers how run length and version count pick the process, and the beverage label printing guide covers the regulated content that has to fit inside the die line once the artwork is built. For breweries in the region, our craft beer label guide for Rochester covers sourcing.

TLF Graphics prints craft beverage labels from Metro Park in Rochester, NY. Send the artwork with the die line and the unwind position, or ask for a template first: contact the team and the prepress department will tell you which file to build in.

Frequently asked questions

What size should a 12 oz can label be?
It depends on the die the job runs on, which is why TLF Graphics publishes templates rather than a single number. The standard 12 oz die lines are 7″ x 3.5″, 8″ x 3.5″, 8.5″ x 3.5″, 8″ x 3.25″ and 8″ x 3.625″, most with a 0.125″ corner radius and one 8″ x 3.5″ version at 0.0156″. A 12 oz sleek can is a different shape and uses its own templates: 6.875″ x 5.375″, 7″ x 5.4″ and 7.125″ x 5.375″.

How much bleed does a can label need?
At least 0.125″, an eighth of an inch, on all four sides. Extend the background of the artwork into the bleed area on every side, and keep important text and images at least 1/16″ inside the die line so nothing is trimmed off.

What is the safe zone on a label?
The margin just inside the die line. No important text or image should sit within 1/16″ of the cut, because that band is where cutting tolerance shows up. Background art runs past the die line into the bleed; content stops short of it.

Which file format should I send?
Adobe Illustrator is the industry standard for labels and packaging, and Adobe PDF, InDesign and Photoshop files are also accepted. Microsoft Publisher, PowerPoint and Word files are generally not suitable for digital prepress. Set the document to CMYK, keep placed images at 300 PPI or better, embed or supply every linked image, and outline the fonts or send them along.

What is unwind direction and why does it matter?
It describes how the labels sit on the roll and which edge of the design comes off first. There are eight positions: 1 to 4 wound out with the labels on the outside of the roll, 5 to 8 wound in with the labels on the inside, each group dispensing top, bottom, right-hand side or left-hand side first. The applicator on the filling line accepts one of them.

How small can a barcode be?
The minimum overall size is 1.175″ wide by 0.816″ high. Normal is 1.469″ by 1.02″, and the maximum is 2.938″ by 2.04″. Leave at least 0.125″ of quiet zone around the symbol and print dark bars on a light background. Red or low-contrast bars will not scan.


t