A graphic overlay is the printed film on the front of a control panel. It carries the legends, the icons, the brand mark and the windows the display reads through, and on a membrane switch it is also the surface a person presses several thousand times a year. It is the part of the machine the operator touches, and it is usually the part specified last.

That ordering causes most overlay failures. The enclosure gets designed, the switch gets designed, and the overlay gets ordered from a drawing that names a thickness and a color and nothing else. Then the panel goes out to a plant that wipes it down with isopropyl alcohol twice a shift, and in eight months the legends are ghosted and a corner has lifted.

This guide covers what belongs on an overlay drawing: the base film, the hardcoat, which surface the ink sits on, the adhesive, the embossing, and the windows. TLF Graphics screen prints overlay panels in Rochester, New York, alongside industrial labels and retail signage, and prints direct to aluminum panels and identification plates with UV LED inkjet.

What a graphic overlay is, and what it is not

An overlay is a printed, die-cut plastic film with an adhesive back. It mounts to a bezel, a metal faceplate or a membrane switch stack. Three things separate it from a label:

  • The ink is usually on the back of the film, not the front. The film becomes the wear surface and the graphics sit underneath it, protected. Suppliers call this second-surface or subsurface printing. One overlay converter describes it as buried graphics, with the ink protected between the material and the adhesive.
  • It is a mechanical part. It has a thickness tolerance, a flatness requirement, a window position that must align with a display, and often an actuation area that flexes.
  • The adhesive is selective. Adhesive is applied only where the overlay bonds. Key areas, vent holes and display windows stay adhesive-free so they can move or stay optically clear.

If your part is a flat printed decal that identifies a machine and never moves, you want an industrial label, not an overlay. TLF’s industrial labeling page covers that side, and the equipment labels guide goes into nameplates and rating plates specifically.

Polyester or polycarbonate: decide this first

Nearly every other decision follows from the base film. The two standard choices are polyester (PET) and polycarbonate (PC), and the industry’s own literature does not agree about them, which is worth knowing before a supplier tells you one is simply better.

Where the sources do agree:

  • Polyester resists more chemicals. Comparison tables from membrane switch manufacturers put PET ahead of PC across a broader range of agents. Polycarbonate is rated only fair against isopropyl alcohol and crazes on contact with MEK and aromatic solvents. If the panel gets wiped with a solvent, that is close to decisive.
  • Polyester survives far more key presses. Published converter figures run to roughly 100,000 cycles for polycarbonate against 1 million for polyester. Some go further and report polycarbonate cracking over a tactile dome in as few as 50,000 operations, and recommend polyester for embossed keys above roughly 250,000 actuations. The numbers differ; the direction does not.
  • Polycarbonate gives better optical clarity, a wider range of surface textures, deeper embossing and flame-rated grades. It also forms into three-dimensional shapes, which polyester does not do as readily.

Where they contradict each other is abrasion. Some suppliers say polycarbonate is harder; others say hard-coated polyester is excellent and the ranking inverts once a coating is applied. Both can be true, because the hardcoat, not the base film, is doing the work.

The practical rule. Specify hard-coated polyester where the panel is wiped down with chemicals or has mechanical keys with real cycle counts. Specify hard-coated polycarbonate where appearance, texture range, deep embossing or a flame rating is the priority, and the switching is capacitive or the overlay is decorative. One UK converter states this plainly: use polycarbonate for non-functional graphic overlays or capacitive switching, not for embossed mechanical keys.

Base film at a glance

Polyester and polycarbonate, by the figures suppliers publish

Vendor-published values. They vary between suppliers, so treat them as a starting point for your own qualification, not as a datasheet.

1,000,000
Actuations published for polyester over a tactile dome
100,000
Actuations published for polycarbonate in the same position
0.010″
Typical emboss height for a rail or pillow key
IP65
Ingress rating converters most often quote for a sealed panel

Sources: published material comparisons and membrane switch design guides from overlay converters and component suppliers; converter sealing specifications. Accessed November 2026.

The hardcoat is the specification, not the film

A bare film scuffs. The hardcoat is what stands between your legends and a decade of fingernails, gloves, grit and cleaning cloths, and the difference it makes is not marginal.

One patent example measured a 2 mm polycarbonate plate with no hardcoat at a haze change of 46.7% after a Taber abrasion test to ASTM D1044. The same material with a hardcoat came in around 5%. That is the gap between a panel that looks fogged after a year and one that does not.

So do not write “polycarbonate, textured” on the drawing and consider the material specified. Name the hardcoated product, and ask the supplier for two documents:

  • The hardcoat’s own chemical resistance chart. Hard-coated polyester films such as MacDermid Autotex AM publish one. Check it against the cleaners your customer actually uses, not against a generic category.
  • A Taber or pencil hardness figure for the coated film. If a supplier quotes abrasion resistance without naming a test method, the number means nothing.

Published haze figures for coated films sit in a narrow band and vendors disagree on which coated film wins, so qualify with a sample rather than a table.

Second-surface printing, and what it costs you

Printing on the reverse of the film puts the base material between the ink and the world. Nothing abrades the graphics because nothing touches them. It is the default for any overlay with a service life measured in years.

Three consequences follow, and all three belong on the drawing:

  • Artwork is mirrored. The print file reads backwards. Supply layered vector art and let the converter handle the reversal rather than flipping it yourself and hoping the registration survives.
  • Color is read through the film. A textured or tinted film shifts the printed color. Approve a printed draw-down on the actual specified film, not a proof on paper.
  • Ink opacity carries the design. Backlit legends and dead-front windows work by controlled opacity: dense enough to hide the lamp when off, open enough to read when lit. That is a print build, specified in layers, not a color swatch.

Screen printing suits this work because it lays down a heavy, opaque ink film on rigid and flexible substrates, which is why TLF uses it for overlay panels and outdoor-durable industrial labels. The print technologies page sets out when screen, digital and flexographic each get chosen.

Adhesive: name the product and the surface

Overlays are bonded with acrylic adhesive transfer tape. The common specification is a 3M 200MP acrylic, supplied as 467MP transfer tape. 3M’s own data sheet positions it for long-term bonding of subsurface-printed polycarbonate or polyester graphic nameplates and overlays to metal and high surface energy plastics, and for membrane switch overlays.

Figures from that data sheet and its distributors:

  • Total tape thickness is listed at 0.06 mm, described as 2.3 mil, against a 2 mil nominal. Sources differ on which number to quote, so take it from the current data sheet rather than a catalog page.
  • The 200MP adhesive is reported to withstand up to 400°F for short periods, and to hold up after humidity and hot and cold cycling.
  • 3M states the adhesive is not adversely affected by outdoor exposure when it is covered by the nameplate or trim part, which is the normal overlay geometry.

Two variants exist for a reason. 467MC carries a paper MicroChannel liner that lets air escape during application, which is how you stop bubbles and wrinkles on a large panel. 467MPF uses a polyester liner for rotary processing. If your assembly is manual and the panel is bigger than a hand span, ask about the channeled liner before you start scrapping parts.

The surface matters as much as the tape. High surface energy substrates such as bare and painted metals bond well with these acrylics. Low surface energy plastics and some powder coats do not, and need a different adhesive family or a primer. Tell the converter what the overlay is sticking to, by material and finish. “Plastic” is not an answer.

Embossing: rail, pillow and dome

Embossing raises part of the overlay so an operator finds a key without looking. Three standard styles:

  • Rail embossing raises only the border of a key, leaving the center flat.
  • Pillow embossing raises the whole key surface into a soft mound. The raised pad presses the dome underneath, which is where the key’s feel comes from. It works with metal or plastic domes.
  • Dome embossing is the third style, a deeper, more pronounced form.

Height is small. Design guides put typical embossing at 0.010″, with one guide giving a range of 0.25 to 0.50 mm, which is 0.010″ to 0.020″. Deeper than that is a conversation about tooling and about whether the base film will take it, and it is the point at which polycarbonate’s willingness to emboss runs into its poor flex life.

Embossing is tooled, so it has a setup cost and a lead time that flat printing does not. Settle the key layout before the tool is cut.

Windows, displays and the sealing claim

Display windows are where overlays are most often rejected on arrival. Specify four things:

  • Position and tolerance, dimensioned from the same datum the enclosure uses. A window that is correct relative to the overlay’s own edge and wrong relative to the bezel is still wrong.
  • Optical treatment: clear, tinted to raise contrast, or anti-glare. Anti-glare costs some sharpness; a tint costs some brightness. Pick against the lighting the machine lives in.
  • Dead-front behavior, if indicators must disappear when unlit.
  • Adhesive-free area behind the window, so there is nothing in the optical path.

On sealing, read the claims carefully. Converters commonly quote IP65 or IP67 for sealed membrane panels and offer higher ratings to a customer drawing, with some stating their perimeter seals meet IP65 and their higher builds meet NEMA 4X. An older design guide describes a watertight NEMA 4 perimeter seal for an overlay set into a recessed panel. These are vendor statements about a build, not independent certifications of your finished product. If your machine has to carry a rating, the enclosure and the overlay get tested together, and the overlay drawing should say which seal design it assumes.

One more item for the drawing: flammability. Where a panel area carries a regulated mark, the rating is recorded against the base material, so the film grade is part of the compliance record. TLF is UL Mark Authorized, and the UL labels guide explains what that authorization covers on the label side.

What to send a supplier so the first article is right

A quotable overlay package has seven items. Missing any one of them is what turns a four-week part into a ten-week part.

  • Layered vector artwork with fonts outlined, printed colors separated, and die lines, emboss areas and adhesive-free zones on their own layers. TLF’s art resources page has the file guidelines.
  • A dimensioned drawing with overall size, window positions, hole positions, radii and tolerances, dimensioned from the mating part’s datum.
  • The base film and hardcoat named as a product, with the texture called out.
  • The adhesive named as a product, with the mating surface’s material and finish stated.
  • Color targets as named references, plus a note that approval is on a draw-down on the specified film.
  • The environment: cleaning agents and frequency, temperature range, UV exposure, and expected actuations per key per year.
  • Quantity and release schedule, because the print method follows the run. Screen printing suits medium to large volumes and outdoor durability; digital suits small to medium quantities with versioning; flexographic suits large quantities on roll.

TLF Graphics has been producing durable printed labels for industrial and durable goods manufacturers for over 40 years, is an ISO 9001:2015 certified company, is UL Mark Authorized, and has no minimum order quantity. The applications on the industrial and durables page run from electronics and handheld devices to HVAC, heavy equipment, medical equipment and fitness equipment, which is the same spread of panels that carry overlays.

Frequently asked questions

Is a graphic overlay the same thing as a membrane switch?
No. The overlay is the printed top layer. A membrane switch is the full stack underneath it: spacer, circuit layers, domes and a tail. You can buy an overlay on its own to mount over a separate switch or a bezel, and many panels are exactly that.

Polyester or polycarbonate for a panel that gets cleaned with alcohol?
Polyester, hard-coated. Published comparisons rate polycarbonate only fair against isopropyl alcohol, and it crazes with MEK and aromatic solvents. Then check the specific hardcoat’s chemical chart against the actual cleaner.

How many key presses will an overlay take?
It depends on the film. Vendors publish about 100,000 cycles for polycarbonate over a dome and about 1 million for polyester, and some report polycarbonate cracking far earlier than that. Give your supplier an actuations-per-year figure and a required service life rather than asking for a maximum.

Why is my overlay printed backwards?
It is printed second surface, on the reverse of the film, so the film protects the ink. The artwork is mirrored during prepress. This is normal and it is what makes the graphics last.

Can the overlay carry variable data, like serial numbers?
Serialization, barcodes and sequential numbering are standard on TLF’s variable data labels. On an overlay, a serialized area is usually handled as a separate printed element or a companion label, because the overlay itself is a tooled, repeating part. Ask when you quote.

Can you print directly onto the panel instead of applying an overlay?
Sometimes. TLF prints direct to object with UV LED inkjet onto aluminum industrial panels, identification plates and other rigid substrates. It removes the adhesive and the die from the problem, though it does not give you embossing or second-surface protection. It is worth asking about for flat metal faceplates.


To spec an overlay panel for your equipment, send the drawing and the artwork to TLF Graphics in Rochester, New York, with the cleaning agents and the expected actuations noted. That is enough to get a real quote and a first article that fits.

t